There is no special way to hang Graphite Insulating Lining Paper, it can be either vertically or horizontally. We recommend that the wall is pasted, polystyrene applied directly to the wall, and time to set is 48 hours.

Yes, we recommend the use of Wallrock Thermal Liner Adhesive only as it has being tested to hang Graphite Insulating Lining Paper. There are many other adhesives which may work but have not being tested.

On average, for Graphite Insulating Lining Paper,  flat surfaces require approximately 3kg of Thermal Liner Adhesive, damaged and textured surfaces require approximately 5kg. *Typical coverage may vary depending on application*. We recommend the use of Wallrock Thermal Liner Adhesive only.

Yes,  so before applying the Graphite insulating lining paper, you must lightly sand the ceiling and size with a PVA or Flake Adhesive, this will form a good surface for the Thermal Liner Adhesive to adhere to.

Yes, the surface of the Graphite Insulating Lining Paper is actually a non-woven Lining Paper.

Two main reasons for lining over the top of Graphite Insulating Lining Paper – 1) Makes it much easier to achieve a nice neat finish with minimal filling and sanding. 2) It helps your investment from damage creating a good base for paint or decorative wallpaper at the same time.

Important – If you are planning to hang lining paper on top of Graphite Insulating Lining Paper, we strongly recommend that you use a non-woven lining paper such as Wallrock Fibreliner Plus, Wallrock Fibreliner or Wallrock premium.Traditional lining paper shrinks and expands when pasted and can cause lifting on the joints In contrast; non-woven lining paper is dimensionally stable and ensures a perfect finish.

No, if the existing wallpaper is firmly stuck to the wall then the Graphite Insulating Lining Paper should cover it, however if it has a deep pattern (more than 2.5mm) or is a Vinyl based paper we would recommend that it is taken off before applying the Graphite Insulating Lining paper. 

Not really, just make sure the walls are clean, dry and solid. If the texture is very deep as with some decorative plaster effects it is advisable to sand down the high points and use extra adhesive to help level the surface. We would advise that after hanging the first drop of Graphite Insulating Lining paper,  stand back and make sure the results are satisfactory.

No you can hang Insulating Lining paper either vertically or horizontally. We recommend that the wall is pasted, polystyrene applied directly to the wall, and time to set is 48 hours.

Yes,  we recommend the use of Wallrock Thermal Liner Adhesive only, as it has been tested to hang Insulating Lining Paper. There are many other adhesives which may work but have not being tested.

On average, when applying Insulating Lining paper on flat surfaces, about 2kg of Thermal Liner Adhesive is required,  for damaged and textured surfaces about 3kg. *Typical coverage may vary depending on application*. We recommend the use of Wallrock Thermal Liner Adhesive only.

Before applying Insulating Lining Paper, we recommend you use a flexible non shrinking decorators caulk or similar good quality non shrinking filler.

Insulating Lining Paper is a ‘Paste The Wall Product Only’. We recommend the adhesive should be applied with a roller directly on to the wall.

Well you have 2 options with Insulating Lining Paper as it will bend around the corner which will give you a rounded corner. Alternatively, you can cut and butt joint at the corner, and this option is best if you are applying a Wallrock Lining Paper or Wallrock Textured paper on top, as it will hide the joint.

Yes, the surface paper of the Insulating Lining paper is actually a non-woven Lining Paper.

Yes, so before applying Insulating Lining paper, you must lightly sand the ceiling and size with a PVA or Flake Adhesive, this will form a good surface for the Thermal Liner Adhesive to adhere to.

Two main reasons for lining over the top of Insulating Lining Paper –  1) Makes it much easier to achieve a nice neat finish with minimal filling and sanding. 2) It helps your investment from damage creating a good base for paint or decorative wallpaper at the same time.

Important – If you are planning to hang lining paper on top of Insulating Lining Paper, we strongly recommend that you use a non-woven lining paper such as Wallrock Fibreliner Plus, Wallrock Fibreliner or Wallrock premium.

Traditional lining paper shrinks and expands when pasted and can cause lifting on the joints In contrast, non-woven lining paper is dimensionally stable and ensures a perfect finish.

No, if the existing wallpaper is firmly stuck to the wall then the Insulating Lining Paper should cover it.  recommend that it is taken off before applying the Insulating Lining Paper. 

Not really, just make sure the walls are clean, dry and solid before applying Insulating Lining Paper. If the texture is very deep as with some decorative plaster effects it is advisable to sand down the high points and use extra adhesive to help level the surface. We would advise that after hanging the first drop stand back and make sure the results are satisfactory.

On average, flat surfaces will take 4kg of adhesive, damaged and textured surfaces take 6kg of adhesive. *Typical coverage of Latex Sound Proof Wall Liner may vary depending on application*. We recommend the use of Wallrock Thermal Liner Adhesive only.

The roll size of Latex Sound Proof Wall Liner  is 10m x 50cm and covers 5 Square Metres – to find out how many rolls you need please use our wallpaper calculator in the top navigation.

Latex Sound Proof Wall Liner is 5mm thick so effectively reducing unwanted noise. 

Latex Sound Proof Wall Liner is a ‘Paste the Wall Product Only’. We recommend the adhesive should be applied with a roller directly onto the wall.

Well you have 2 options with Latex Sound Proof Wall Liner as it will bend around the corner and this will give you a rounded corner. Alternatively you can cut and butt joint at the corner, this option is best if you are applying a Wallrock Lining Paper or Wallrock Textured paper on top as it will hide the joint.

Latex Sound Proof Wall Liner is better at absorbing noise entering the room through walls and ceilings – so if you have a problem with noisy neighbours and there is no chance of your neighbour doing anything himself to isolate the source, then this is the best product to use.

Always apply the cream foam side of the Latex Sound proof Wall Liner to the wall leaving the rough hard surface facing outwards.

Yes, so before applying Latex Sound Proof Wall Liner you must lightly sand the ceiling and size with a PVA Adhesive which will form a good surface for the Thermal Liner Adhesive to adhere to.

Latex Sound proof Wall Liner is tightly wound up during manufacture, therefore we recommend that the rolls are opened and left on their ends to unravel naturally for approximately 24 hours before hanging. 

Yes it is, and you should make sure that the first layer of Latex Sound Proof Wall Liner  has dried out completely before applying another layer. You must use the Wallrock Thermal Liner Adhesive.

Yes, and the surface of the Latex Sound Proof Wall Liner has a rough textured finish. For a smooth finish use Wallrock Fibreliner, Fibreliner Plus or Wallrock Premium.

Two main reasons – 1) Makes it much easier to achieve a nice neat finish with minimal filling and sanding. 2) It helps your investment from damage creating a good base for paint or decorative wallpaper at the same time.Important – If you are planning to hang lining paper on top of Latex Sound Proof Wall Liner, we strongly recommend that you use a non-woven lining paper such as Wallrock Fibreliner Plus, Wallrock Fibreliner or Wallrock premium.Traditional lining paper shrinks and expands when pasted and can cause lifting on the joints In contrast; non-woven lining paper is dimensionally stable and ensures a perfect finish.

No, if the existing wallpaper is firmly stuck to the wall then Latex Sound Proof Wall Liner should cover over it,. However, if it has a deep pattern (more than 3mm) or is a Vinyl based paper we would recommend that it is taken off before applying the Latex Sound Proof Wall Liner.

Yes – Latex Sound Proof Wall Liner really does work as it is made from specially developed sound absorbing foam and laminated with a thick lining paper. The Latex structure acts like a sponge, reducing echo and deadening noise, and is particularly effective in combating high frequency sounds.

Yes, and the surface of the Latex Sound Proof Wall Liner has a rough textured finish. For a smooth finish use Wallrock Fibreliner, Fibreliner Plus or Wallrock Premium.

Two main reasons – 1) Makes it much easier to achieve a nice neat finish with minimal filling and sanding. 2) It helps your investment from damage creating a good base for paint or decorative wallpaper at the same time.Important – If you are planning to hang lining paper on top of Latex Sound Proof Wall Liner, we strongly recommend that you use a non-woven lining paper such as Wallrock Fibreliner Plus, Wallrock Fibreliner or Wallrock premium.Traditional lining paper shrinks and expands when pasted and can cause lifting on the joints In contrast; non-woven lining paper is dimensionally stable and ensures a perfect finish.

Two main reasons for lining over the top of Insulating Lining Paper –  1) Makes it much easier to achieve a nice neat finish with minimal filling and sanding. 2) It helps your investment from damage creating a good base for paint or decorative wallpaper at the same time.

Important – If you are planning to hang lining paper on top of Insulating Lining Paper, we strongly recommend that you use a non-woven lining paper such as Wallrock Fibreliner Plus, Wallrock Fibreliner or Wallrock premium.

Traditional lining paper shrinks and expands when pasted and can cause lifting on the joints In contrast, non-woven lining paper is dimensionally stable and ensures a perfect finish.

We recommend lining over the top of Sound Proof Insulating Liner for Two main reasons -1) Makes it much easier to achieve a nice neat finish with minimal filling and sanding. 2) It helps your investment from damage creating a good base for paint or decorative wallpaper at the same time.

Important – If you are planning to hang lining paper on top of Sound Proof Insulating Liner, we strongly recommend that you use a non-woven lining paper such as Wallrock Fibreliner Plus, Wallrock Fibreliner or Wallrock premium.Traditional lining paper shrinks and expands when pasted and can cause lifting on the joints In contrast; non-woven lining paper is dimensionally stable and ensures a perfect finish.

Yes, the surface of Wallrock KV600 Thermal Liner is actually Wallrock Fibreliner which is a non-woven Lining Paper.

The answer is Yes you can.  The surface of the Wallrock Thermal Liner  is actually Wallrock Fibreliner which is a non-woven Lining Paper.

Two main reasons for lining over the top of  Wallrock Thermal Liner – 1) Makes it much easier to achieve a nice neat finish with minimal filling and sanding. 2) It helps your investment from damage creating a good base for paint or decorative wallpaper at the same time.

Important – If you are planning to hang lining paper on top of Wallrock Thermal Liner, we strongly recommend that you use a non-woven lining paper such as Wallrock Fibreliner Plus, Wallrock Fibreliner or Wallrock premium.

Traditional lining paper shrinks and expands when pasted and can cause lifting on the joints In contrast; non-woven lining paper is dimensionally stable and ensures a perfect finish.

Two main reasons for lining over the top of Graphite Insulating Lining Paper – 1) Makes it much easier to achieve a nice neat finish with minimal filling and sanding. 2) It helps your investment from damage creating a good base for paint or decorative wallpaper at the same time.

Important – If you are planning to hang lining paper on top of Graphite Insulating Lining Paper, we strongly recommend that you use a non-woven lining paper such as Wallrock Fibreliner Plus, Wallrock Fibreliner or Wallrock premium.Traditional lining paper shrinks and expands when pasted and can cause lifting on the joints In contrast; non-woven lining paper is dimensionally stable and ensures a perfect finish.

Always apply the coloured foam side of the Sound Proof Insulating Liner to the wall leaving the flat smooth surface facing outwards.

On average, on flat surfaces 2kg, on damaged and textured surfaces 3kg. *Typical coverage for Sound Proof Insulating Liner may vary depending on application*. We recommend the use of Wallrock Thermal Liner Adhesive only.

The roll size of Sound Proof Insulating Liner is 5m x 50cm and covers 2.5 Square Metres – To find out how many rolls you need, please use our wallpaper calculator in the top navigation.

Sound Proof Insulating Liner is 6mm thick providing a simple DIY solution for homes and businesses that suffer from the inconvenience of sound pollution.

Sound Proof Insulating Liner is a ‘Paste the Wall Product Only’. We recommend the adhesive should be applied with a roller directly on to the wall.

Sound Proof Insulating Liner is best suited to rooms where you want to absorb the noise within it. For example, noise could be entering the room through an open window, single glazed window or from a source within it (eg; vacuum cleaner). In such cases, internal application of the Sound Proof Insulating Liner will help absorb sound and stop it bouncing around as well as reduce the noise escaping through surfaces into other rooms. In an incidence of noise problems from an adjoining room it can be used to best effect by using it in the room that is generating the noise, not in the room adjacent.

Well you have 2 options, Sound Proof Insulating Liner will bend around the corner and this will give you a rounded corner. Alternatively you can cut and butt joint at the corner, this option is best if you are applying a Wallrock Lining Paper or Wallrock Textured paper on top as it will hide the joint.

Yes, but before applying Sound Proof Insulating Liner  you must lightly sand the ceiling and size with a PVA or Flake Adhesive, which will form a good surface for the Thermal Liner Adhesive to adhere to.

The roll of Sound Proof insulating Liner is tightly wound up during manufacture, so therefore we recommend that the rolls are opened and left on their ends to unravel naturally for approximately 24 hours before hanging.

Yes, just make sure that the first layer of Sound Proof Insulating Liner has dried out completely before applying another layer; you must use the Wallrock Thermal Liner Adhesive.

Yes you can because the surface of the Sound Proof Insulating Liner is a smooth Lining Paper.

We recommend lining over the top of Sound Proof Insulating Liner for Two main reasons -1) Makes it much easier to achieve a nice neat finish with minimal filling and sanding. 2) It helps your investment from damage creating a good base for paint or decorative wallpaper at the same time.

Important – If you are planning to hang lining paper on top of Sound Proof Insulating Liner, we strongly recommend that you use a non-woven lining paper such as Wallrock Fibreliner Plus, Wallrock Fibreliner or Wallrock premium.Traditional lining paper shrinks and expands when pasted and can cause lifting on the joints In contrast; non-woven lining paper is dimensionally stable and ensures a perfect finish.

No, if the existing wallpaper is firmly stuck to the wall then Sound Proof Insulating Liner should cover it.  However if it has a deep pattern (more than 3mm) or is a Vinyl based paper we would recommend that it is taken off before applying the Sound Proof Insulating Liner.

Yes, Sound Proof Insulating Liner is made from specially developed sound absorbing foam and laminated with a thick lining paper. The polyurethane foam structure acts like a sponge, reducing echo and deadening noise, and is particularly effective in combating high frequency sounds.

Always apply Wallrock KV600 Thermal Liner with the fluffy side to the wall leaving the smooth flat side of the liner facing outwards.

On average, for flat surfaces, you will need 7kg of Wallrock KV600 Thermal Liner Adhesive, and for damaged and textured surfaces 10kg. *Typical coverage may vary depending on application*.

The roll size of Wallrock KV600 Thermal Liner is 15m x 1m and covers 15 Square Metres – to find out how many rolls you need please use our wallpaper calculator in the top navigation.

Wallrock KV600 Thermal Liner is a ‘Paste the Wall Product Only’. We recommend the adhesive should be applied with a roller directly onto the wall.

Well you have 2 options with Wallrock KV600 Thermal liner

1) It will bend around the corner and this will give you a rounded corner,

2) You can cut and butt joint at the corner – this option is best if you are applying a Wallrock Lining Paper or Wallrock Textured paper on top as it will hide the joint.

Yes, but before applying Wallrock KV600 Thermal Liner, you must lightly sand the ceiling and size with a PVA or Flake Adhesive, this will form a good surface for the Thermal Liner Adhesive to adhere to.

Yes, the surface of Wallrock KV600 Thermal Liner is actually Wallrock Fibreliner which is a non-woven Lining Paper.

Two main reasons, 1) Makes it much easier to achieve a nice neat finish with minimal filling and sanding. 2) It helps your investment from damage creating a good base for paint or decorative wallpaper at the same time.Important – If you are planning to hang lining paper on top of Wallrock KV600 Thermal Liner, we strongly recommend that you use a non-woven lining paper such as Wallrock Fibreliner Plus, Wallrock Fibreliner or Wallrock premium.Traditional lining paper shrinks and expands when pasted and can cause lifting on the joints In contrast; non-woven lining paper is dimensionally stable and ensures a perfect finish.

No, if the existing wallpaper is firmly stuck to the wall then Wallrock KV600 Thermal Liner should cover it, however if it has a deep pattern (more than 2.5mm) or is a Vinyl based paper we would recommend that it is taken off before applying the KV600 Thermal Liner. 

I have some really badly textured walls so do I need to take special precautions when applying Wallrock KV600 Thermal Liner over such poor surfaces?

Not really, just make sure the walls are clean, dry and solid before applying Wallrock KV600 Thermal Liner . If the texture is very deep as with some decorative plaster effects it is advisable to sand down the high points and use extra adhesive to help level the surface. We would advise that after hanging the first drop, stand back and make sure the results are satisfactory.

Where in the house can I use it to best effect?

Wallrock KV600 Thermal Liner is certainly most effective as an energy saver on outside walls and especially so if the walls are of solid construction (without cavities). However other key benefits of the product include acting as a sound insulation and covering over textured surfaces to produce a flat surface.

I remember those old polystyrene insulation tiles that were a fire hazard?

Wallrock KV600 Thermal Liner is classified as “E” according to DIN EN 13501-1 in relation to fire behaviour, which corresponds to “B2” (normally inflammable) according to the standard DIN 4102-1.

How it will look around light switches and skirting boards?

Wallrock KV600 Thermal Liner is 4mm thick and a neat finish is therefore possible in most applications, skirting, coving or light switches for example do not appear to be ‘sunk’ below the wall surface. Don’t forget Thermal Liner works best on outside walls, significant benefits can be achieved without the need to apply it to every internal surface.

Yes, and you must use ‘Wallrock Thermal Liner Adhesive’ as it is specially formulated to hang Wallrock KV600 Thermal Liner. We however ‘Do Not’ recommend you use within shower areas.

Wallrock KV600 Thermal Liner works in a different way to traditional insulating products. For a start we realise that rooms are rarely heated constantly 24 / 7. So Thermal Liner works by reducing warm up times dramatically as is begins to work immediately the heating is turned on because it is on the inside of the outside wall. Conventional products only work after the inside wall has being heated which can take hours – the very time you are likely to be in the room. Once the room has warmed up Wallrock Thermal continues to resist energy loss.

Yes you will save money and notice a significant change with Wallrock KV600 Thermal Liner,  especially when the heating is first turned on as room warm up time is reduced dramatically and the air currents that make you feel cold whilst the room warms up are also reduced. This is of course in addition to all the other benefits such as a reduction in noise through the treated wall.

On average, flat surfaces of Wallrock Thermal Liner use 3.5kg of Thermal liner Adhesive , damaged and textured surfaces use 5kg. *Typical coverage may vary depending on application*.

Yes, but before applying Wallrock Thermal Liner,  you must lightly sand the ceiling and size with a PVA or Flake Adhesive. This will form a good surface for the Thermal Liner Adhesive to adhere to.

Yes you can use Wallrock Thermal Liner in bathrooms, and you must use ‘Thermal Liner Adhesive’ as it is specially formulated to hang Thermal Liner. However,  we  ‘Do Not’ recommend you use within shower areas.

Yes, we recommend the use of Wallrock Thermal Liner Adhesive only as it has being tested to hang Graphite Insulating Lining Paper. There are many other adhesives which may work but have not being tested.

On average, for Graphite Insulating Lining Paper,  flat surfaces require approximately 3kg of Thermal Liner Adhesive, damaged and textured surfaces require approximately 5kg. *Typical coverage may vary depending on application*. We recommend the use of Wallrock Thermal Liner Adhesive only.

Yes,  we recommend the use of Wallrock Thermal Liner Adhesive only, as it has been tested to hang Insulating Lining Paper. There are many other adhesives which may work but have not being tested.

On average, flat surfaces use approximately 3.5kg of Thermal Liner Adhesive, where as damaged and textured surfaces use approximately 5kg. *Typical coverage may vary depending on application*.

Yes, but before applying Wallrock Thermal Liner,  you must lightly sand the ceiling and size with a PVA or Flake Adhesive. This will form a good surface for the Thermal Liner Adhesive to adhere to.

Not really, just make sure the walls are clean, dry and solid before applying Wallrock Thermal Liner. If the texture is very deep as with some decorative plaster effects it is advisable to sand down the high points and use extra adhesive to help level the surface. We would advise that after hanging the first drop stand back and make sure the results are satisfactory.

Wallrock Thermal Liner works in a different way to traditional insulating products. For a start we realise that rooms are rarely heated constantly 24 / 7. So Wallrock Thermal Liner works by reducing warm up times dramatically as is begins to work immediately the heating is turned on because it is on the inside of the outside wall. Conventional products only work after the inside wall has being heated which can take hours – the very time you are likely to be in the room. Once the room has warmed up Wallrock Thermal continues to resist energy loss.

With Wallrock Thermal Liner, yes you will, especially when the heating is first turned on as room warm up time is reduced dramatically and the air currents that make you feel cold whilst the room warms up are also reduced. This is of course in addition to all the other benefits such as a reduction in noise through the treated wall.

Yes you can use Wallrock Thermal Liner in bathrooms, and you must use ‘Thermal Liner Adhesive’ as it is specially formulated to hang Thermal Liner. However,  we  ‘Do Not’ recommend you use within shower areas.

Wallrock Thermal Liner is less than 3.2mm thick and a neat finish is therefore possible in most applications, skirting, coving or light switches for example do not appear to be ‘sunk’ below the wall surface. Don’t forget,  WallrockThermal Liner works best on outside walls, significant benefits can be achieved without the need to apply it to every internal surface.

I remember the old polystyrene insulation tiles that were a fire hazard, so I have worries in this regard?

Wallrock Thermal Liner is classified as “E” according to DIN EN 13501-1 in relation to fire behaviour, which corresponds to “B2” (normally inflammable) according to the standard DIN 4102-1.

When using Wallrock Thermal Liner, Walls inside the building which are exposed to the weather on the opposite side.

Wallrock Thermal Liner is certainly most effective as an energy saver on outside walls and especially so if the walls are of solid construction (without cavities). However other key benefits of the product include acting as a sound insulation and covering over textured surfaces to produce a flat surface.

No, if the existing wallpaper is firmly stuck to the wall then Wallrock Thermal Liner should cover it, however if it has a deep pattern (more than 2.5mm) or is a Vinyl based paper we would recommend that it is taken off before applying the Thermal Liner. 

Two main reasons for lining over the top of  Wallrock Thermal Liner – 1) Makes it much easier to achieve a nice neat finish with minimal filling and sanding. 2) It helps your investment from damage creating a good base for paint or decorative wallpaper at the same time.

Important – If you are planning to hang lining paper on top of Wallrock Thermal Liner, we strongly recommend that you use a non-woven lining paper such as Wallrock Fibreliner Plus, Wallrock Fibreliner or Wallrock premium.

Traditional lining paper shrinks and expands when pasted and can cause lifting on the joints In contrast; non-woven lining paper is dimensionally stable and ensures a perfect finish.

The answer is Yes you can.  The surface of the Wallrock Thermal Liner  is actually Wallrock Fibreliner which is a non-woven Lining Paper.

Always apply Wallrock Thermal Liner with the fluffy side to the wall leaving the smooth flat side facing outwards.

Wallrock Thermal Liner is a ‘Paste the Wall Product Only’. We recommend the adhesive should be applied with a roller directly onto the wall.

Well you have 2 options – Wallrock Thermal liner will bend around the corner and this will give you a rounded corner, alternatively you can cut and butt joint at the corner, this option is best if you are applying a Wallrock Lining Paper or Wallrock Textured paper on top as it will hide the joint.

The roll size of  Wallrock Thermal Liner  is 10m x 75cm and covers 7.5 Square Metres – to find out how many rolls you need please use our wallpaper calculator in the top navigation.

On average, flat surfaces of Wallrock Thermal Liner use 3.5kg of Thermal liner Adhesive , damaged and textured surfaces use 5kg. *Typical coverage may vary depending on application*.

Yes, just make sure that the first layer of Sound Proof Insulating Liner has dried out completely before applying another layer; you must use the Wallrock Thermal Liner Adhesive.

On average, on flat surfaces 2kg, on damaged and textured surfaces 3kg. *Typical coverage for Sound Proof Insulating Liner may vary depending on application*. We recommend the use of Wallrock Thermal Liner Adhesive only.

Yes it is, and you should make sure that the first layer of Latex Sound Proof Wall Liner  has dried out completely before applying another layer. You must use the Wallrock Thermal Liner Adhesive.

Well you have 2 options as Wallrock Thermal liner will bend around the corner and this will give you a rounded corner.  Alternatively you can cut and butt joint at the corner, this option is best if you are applying a Wallrock Lining Paper or Wallrock Textured paper on top as it will hide the joint.

On average, flat surfaces use approximately 3.5kg of Thermal Liner Adhesive, where as damaged and textured surfaces use approximately 5kg. *Typical coverage may vary depending on application*.

The roll size for Wallrock Thermal Liner  is 10m x 75cm and covers 7.5 Square Metres – to find out how many rolls you need please use our wallpaper calculator in the top navigation.

Always apply your Wallrock Thermal Liner with the fluffy side of the liner to the wall leaving the smooth flat side facing outwards.